手提袋的印刷设计包括尺寸、印刷排版方式等内容，尺寸需要根据客户的需求来确定，而其印刷排版方式则是手提袋印刷设计的，常用的手提袋印刷设计的方法主要体现在模压方法和开纸方法两个方面。

The printing design of handbags includes size, printing and typesetting method, etc. the size needs to be determined according to the needs of customers, and its printing and typesetting method is the focus of handbag printing design. The commonly used methods of handbag printing design are mainly embodied in two aspects: molding method and paper opening method.

手提袋印刷设计的模压方法

Molding method for printing design of handbag

模压后折叠成型时，有的压痕线是使印刷面朝外折叠，而有的压痕线是使印刷面朝内折叠。手提纸袋在使用过程中容易破裂的地方是长方形底部的四边和四条竖线，这几条折痕都是印刷面朝外折叠的。

When folding and forming after molding, some indentation lines fold the printing surface outward, while some indentation lines fold the printing surface inward. The four sides and four vertical lines at the bottom of the rectangle are easy to break during the use of the portable paper bag. These folds are folded outward on the printing surface.

为了减少手提纸袋在折叠过程中造成的破坏，手提纸袋压痕宜采用背面压痕，即压痕时钢线和纸张的背面接触，使折痕向印刷面凸出。由于压痕线要和纸张正面图像对准，这就要求印刷时的叼口边、侧规边应该和模压时的叼口边、侧规边一致。

In order to reduce the damage caused by the folding process of the portable paper bag, the back indentation should be used for the indentation of the portable paper bag, that is, the steel wire contacts the back of the paper during the indentation, so that the crease protrudes towards the printing surface. Since the indentation line should be aligned with the front image of the paper, it is required that the nip edge and side gauge edge during printing should be consistent with those during molding.

济南手提袋印刷设计的开纸方法

Paper opening method of Jinan handbag printing design

因为印张上有1cm左右宽度的叼口边是印不到的，而且成品范围以外还需要有规矩线、色标等,所以对于一般印件，都先将纸张裁得比成品大，印后加工时，再用切纸机或模切机将周围废纸边切掉。手提纸袋的压痕加工如果是用厚纸板代替压痕线，模切和压痕就不宜同时进行，所以手提纸袋一般只进行压痕加工，而不进行模切加工。

Because the mouth edge with a width of about 1cm on the printing sheet cannot be printed, and there are regular lines, color codes, etc. outside the scope of the finished product, for general printing pieces, the paper is first cut larger than the finished product, and then the surrounding waste paper edges are cut off with a paper cutter or die cutter during post printing processing. If the indentation processing of portable paper bags is to replace the indentation line with thick cardboard, die cutting and indentation should not be carried out at the same time, so portable paper bags generally only carry out indentation processing, not die cutting processing.

如果压痕前用切纸机将纸边裁切掉，将会影响压痕的定位精度。因此，一般采用的方法是印刷前将纸张裁切成成品的展开尺寸大小，印刷后只进行压痕加工，不再需要裁切或模切，这样既节省了模压版的制作费用和纸张成本，又使生产过程变得更有效率。

If the paper edge is cut off by the paper cutter before the indentation, the positioning accuracy of the indentation will be affected. Therefore, the general method is to cut the paper into the unfolding size of the finished product before printing, and only carry out indentation processing after printing, without cutting or die cutting, which not only saves the production cost of the template and the paper cost, but also makes the production process more efficient.

模压方法和开纸方法是在手提袋印刷设计时常见的两种形式，一个手提袋不管需要设计还需要的印刷才能体现出来产品的价值。所以，手提袋的设计应该简单、提拿结实，具有防护和贮藏功能。

Molding method and paper opening method are two common forms in the printing design of handbags. A handbag needs both design and perfect printing to reflect the value of the product. Therefore, the design of the handbag should be simple and firm, with protection and storage functions.

手提袋的防护和结实离不开印刷技术，需要在手提袋的印刷设计中体现出来，以上便是问题的相关解答了，您可以参考使用，更多关于印刷事项就来我们网站http://www.xinfengyinshua.cn看看啊！

The protection and firmness of handbags are inseparable from printing technology, which needs to be reflected in the printing design of handbags. The above is the relevant answer to the problem. You can refer to it. For more information about printing, please come to our website http://www.xinfengyinshua.cn Look!